Understand › Staking
Choosing a Flare validator: the checklist
The highest yield is only one criterion out of six. Consistency, eligibility, remaining capacity, node end dates, fees and the size of your own stake also matter, and can be checked in a few minutes.
Staking FLR on the P-chain means locking them with a validator until a chosen date, with a minimum of 50,000 FLR and 2 weeks (official documentation). Once the stake is committed, you cannot change your mind before the end: the validator has to be chosen beforehand. This checklist covers the six points to check, with figures from the recent period, recalculated every epoch from the Flare Foundation’s public files.
It is not a ranking, nor investment advice: the aim is to know how to read the figures given by the validator comparison.
1. Compare net yield, over several epochs
The figure that matters is the net yield: what you would actually have received, after fees, as a percentage per year. Over the epochs 443 to 450, half of the 97 validators tracked paid between 8.20% and 9.95% per year (median: 9.11%).
Compare an average over several epochs rather than the last one alone: the comparison offers 4, 8 or 26 epochs. And keep in mind that these are past figures, paid in FLR, whose price varies.
2. Check consistency and eligibility
A validator that does not meet the protocol’s minimum conditions during an epoch receives nothing for that epoch, and neither do its stakers. Flarescope counts these epochs as zero in the average, since that is what you would have received.
Over the period, 9 validators missed at least one epoch. Their median yield falls to 6.29%, against 9.21% for those that were eligible in every epoch. The “Eligibility” column of the comparison gives the number of successful epochs, and the “Always eligible” filter excludes the others.
The “Min – max” column shows the gap between the worst and the best epoch. For the median validator, this gap is 0.91 point; a much wider gap signals an irregular yield.
3. Check that there is room left
A node cannot receive more than 15 times its validator’s own stake, nor more than 300 million FLR. A validator whose nodes are all full no longer accepts new stake.
Yet the most profitable validators are often the smallest, and therefore the quickest to fill up (the article Staking your FLR: what a validator really pays explains why). At the last P-chain reading, 13 validators no longer had room for the 50,000 FLR minimum; their median yield was 10.24%, against 9.00% for those that still had room. Full validators among the ten best yields of the period: 3.
The “Remaining capacity” column and the “With capacity” filter of the comparison help you avoid aiming at an inaccessible validator.
4. Look at the end date of the nodes
Each validator node is registered until an end date, and a stake cannot last beyond it. At the last reading, 40 validators had at least one node ending in less than 30 days. This is not necessarily a bad sign: many validators renew their nodes. But it limits the possible duration with them, and a node that is not renewed stops paying.
The “Node end” column of the comparison shows the nearest date, and the simulator checks that the nodes stay active for the whole chosen duration.
5. Read the fee, without overrating it
A validator takes two fees: its P-chain node fee on the staking share, and its FTSO fee on the mirror share. Both are already deducted from the net yield shown.
Most nodes apply 20%, a few 10%. Since the staking share is the same everywhere apart from the fee, going from 20% to 10% raises it from 2.83% to about 3.18% per year. That is real, but smaller than the differences due to eligibility or the validator’s size: a low fee does not make up for an irregular validator.
6. Take your own stake into account
Part of a validator’s rewards is shared among everyone who has staked with it. By adding your FLR, you dilute this share, for yourself as for the others. For a small amount, the effect is negligible; for several million FLR with a small validator, it becomes noticeable.
The simulator calculates this dilution for a given amount and duration, and compares up to three validators. Nothing prevents you from splitting a stake between several validators, within the limit of 50,000 FLR minimum per stake.
Key point
According to the data, eligibility, remaining capacity and node end dates are what rule out the most validators, well before the fee. The comparison lets you check them in a few minutes.
And security
Flarescope never asks you to connect a wallet: staking is done from your own wallet, with the tool of your choice. Be wary of any site or message offering to “stake for you” or asking for your secret phrase: no serious service asks for it.
The figures in this article and their limits are described on the Method page. Past yield does not guarantee future yield.